2024 EditionDivision B · 20 articles
Part 1 — General
Section 1.1.General
1.1.1.Application
1.1.1.1.Application
(1) This Part applies to all buildings covered in this Code.
1.1.2.Reserved
1.1.3.Climatic and Seismic Data
1.1.3.1.Climatic and Seismic Values
(1) The climatic and seismic values required for the design of buildin gs under this Code shall be in conformance with the climatic and seismic values provided in MMAH Supplementary Standard SB-1, “Climatic and Seismic Data”.
(2) The outside winter design temperatures determined from MMAH Supplementary Standard SB-1, “Climatic and Seismic Data”, shall be those listed for the January 2.5% values. (See Note A- .(2))
1.1.3.2.Depth of Frost Penetration
(1) Depth of frost penetration shall be established on the basis of local experience.
1.1.4.Reserved
Section 1.2.Definitions
1.2.1.Definitions
1.2.1.1.Non-defined Terms
(1) Words and phrases used in Division B that are not included in the list of definitions in Articles ., . and . of Division A and are not defined in another provision of this Code shall have the meanings that are commonly assigned to them in the context in which they are used, taking into account the specialized use of terms by the various trades and professions to which the terminology applies.
(2) Where objectives and functional s tatements are referred to in Division B, they shall be the objectives and functional statements described in Parts 2 and 3 of Division A.
(3) Where acceptable solutions are referred to in Division B, they shall be the provisions stated in Parts 2 to 12.
1.2.1.2.Defined Terms
(1) Words that appear in italics are defined in Article . of Division A and in the Building Code Act, 1992.
1.2.2.Symbols and Other Abbreviations
1.2.2.1.Symbols and Other Abbreviations
(1) The symbols and other abbreviations in Division B shall have the meanings assigned to them in Article . of Division A and Article .
Section 1.3.Referenced Documents and
1.3.1.Referenced Documents
1.3.1.1.Effective Date
(1) Unless otherwise specified in this Code, the documents referenced in this Code shall include all amendments, revisions, reaffirmations, reapprovals, addenda and supplements effective to July 15, 2019.
1.3.1.2.Applicable Editions
(1) Where documents are referenced in this Code, they shall be in the editions designated in Table .
Table 1.3.1.2. Documents Referenced in the Building Code Forming Part of Sentence 1.3.1.2.(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| ACGIH | 2013, 28th Edition | Industrial Ventilation: A Manual of Recommended Practice for Design | 2.4.2.5.(1) 6.2.1.1.(1) 6.3.2.14 .(2) |
| ACI | 355.2-19 | Qualification of Post-Installed Mecha nical Anchors in Concrete (ACI 355.2-19) and Commentary | 4.1.8.18 .(7) |
| ACI | 355.4M-19 | Qualification of Post-Installed Adhesive Anchors in Co ncrete (ACI 355.4M-19) and Commentary | 4.1.8.18 .(7) |
| AISI | S201-12 | North American Standard for Cold Formed Steel Framing – Product Data 2012 Edition | 9.24.1.2 .(1) |
| ANSI | A135.6-2012 | Engineered Wood Siding | Table 5.9.1.1 . 9.27.9.1 .(1) |
| ANSI | A208.1-2009 | Particleboard | 9.23.15.2.(3) 9.29.9.1 .(1) 9.30.2.2 .(1) |
| ANSI | E1.21-2013 | Entertainment Technology - Temporary Struct ures Used for Technical Production of Outdoor Entertainment Events | 3.17.2.8.(1) |
| ANSI/ASHRAE | 62.1-2016 | Ventilation for Acceptable Indoor Air Quality | 6.3.1.1.(2) 6.3.1.1.(3) 6.3.2.2.(1) 6.3.2.10 .(15) |
| ANSI/CSA | ANSI Z21.22-2015 / CSA 4.4-2015 | Relief Valves for Hot Water Supply Systems | 7.2.10.11 .(1) |
| APA | ANSI/APA PRG 320- 2018 | Standard for Performance-Rated Cros s-Laminated Timber | 3.1.6.3.(3) |
| APHA/AWWA/ WEF | 2023, 24th Edition | Standard Methods for the Exami nation of Water and Wastewater | 8.9.2.4.(1) |
| ASCE | ASCE/SEI 49-12 | Wind Tunnel Testing for Buildings and Ot her Structures | 4.1.7.14 .(1) |
| ASHRAE | 2021 | Fundamentals | 5.2.1.3.(1) 6.2.1.1.(1) 6.3.2.12 .(1) 7.6.3.1.(2) 7.7.3.1.(1) 9.32.2.3 .(4) 9.32.3.2 .(1) 9.33.4.1 .(1) 9.33.6.2 .(8) 9.33.6.7 .(2) |
| ASHRAE | 2023 | HVAC Applications | 6.2.1.1.(1) 6.3.2.12 .(1) 7.6.3.1.(2) 7.7.3.1.(1) 9.32.2.3 .(4) 9.32.3.2 .(1) 9.33.4.1 .(1) 9.33.6.2 .(8) 9.33.6.7 .(2) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| ASHRAE | 2020 | HVAC Systems and Equipme nt | 6.2.1.1.(1) 6.3.2.12 .(1) 7.6.3.1.(2) 7.7.3.1.(1) 9.32.2.3 .(4) 9.32.3.2 .(1) 9.33.4.1 .(1) 9.33.6.2 .(8) 9.33.6.7 .(2) |
| ASHRAE | 2022 | Refrigeration | 6.2.1.1.(1) 6.3.2.12 .(1) 7.6.3.1.(2) 7.7.3.1.(1) 9.32.2.3 .(4) 9.32.3.2 .(1) 9.33.4.1 .(1) 9.33.6.2 .(8) 9.33.6.7 .(2) |
| ASHRAE | Guideline 12-2000 | Minimizing the Risk of Legione llosis Associated with Building Water Systems | 6.2.1.1.(1) 6.3.2.15 .(9) 6.3.2.16 .(1) |
| ASME | A112.19.8-2007 | Suction Fittings for Use in Swimming Pools, Wading Pools, Spas, and Hot Tubs | 3.12.4.1 .(9) |
| ASME | B16.3-2016 | Malleable Iron Threaded Fittings: Classes 150 an d 300 | 7.2.6.6.(1) |
| ASME | B16.4-2016 | Gray Iron Threaded Fittings: Classes 125 and 250 | 7.2.6.5.(1) Table 7.2.11.2 . |
| ASME | B16.5-2017 | Pipe Flanges and Flanged Fittings: NPS ½ through NPS 24 Metric/Inch Standard | 7.2.6.12 .(1) |
| ASME | B16.9-2018 | Factory-Made Wrought Buttwelding Fittings | 7.2.6.11 .(1) 7.2.6.14 .(1) |
| ASME | B16.12-2009 | Cast Iron Threaded Drai nage Fittings | 7.2.6.3.(1) |
| ASME | B16.15-2018 | Cast Copper Alloy Threaded Fittings: Classes 125 and 250 | 7.2.7.3.(1) |
| ASME | B16.18-2018 | Cast Copper Alloy Solder Joint Pressure Fittings | 7.2.7.6.(1) 7.2.7.6.(2) Table 7.2.11.2 . |
| ASME | B16.22-2018 | Wrought Copper and Copper Alloy S older Joint Pressure Fittings | 7.2.7.6.(1) Table 7.2.11.2 . |
| ASME | B16.23-2016 | Cast Copper Alloy Solder Joint Drainage Fittings: DWV | 7.2.7.5.(1) |
| ASME | B16.24-2016 | Cast Copper Alloy Pipe Flanges and Flanged Fitting s: Classes 150, 300, 600, 900, 1500 an d 2500 | 7.2.7.2.(1) |
| ASME | B16.26-2013 | Cast Copper Alloy Fittings for Flared Copper Tubes | 7.2.7.7.(1) 7.2.7.7.(2) Table 7.2.11.2 . |
| ASME | B16.29-2018 | Wrought Copper and Wrought Copper Alloy Solde r Joint Drainage Fittings - DWV | 7.2.7.5.(1) |
| ASME | ANSI/ASME B18.6.1- 1981 | Wood Screws (Inch Series) | Table 5.9.1.1 . |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| ASME | B31.9-2017 | Building Services Piping | 7.3.2.8.(1) |
| ASME | B36.19M-2018 | Stainless Steel Pipe | 7.2.6.10 .(1) |
| ASME/CSA | ASME A17.1-2016 / CSA B44-16 | Safety Code for Elevators and Escalators | 3.5.2.2.(1) Table 4.1.5.11 . Table 4.1.8.18 . 7.4.3.6.(1) |
| ASME/CSA | ASME A112.3.4-2018 / CSA B45.9-18 | Macerating Toilet Systems and Waste-Pump ing Systems for Plumbing Fixtures | 7.2.2.2.(1) |
| ASME/CSA | ASME A112.4.2- 2015/CSA B45.16-15 | Personal hygiene devices for water closets | 7.2.2.2.(1) |
| ASME/CSA | ASME A112.4.14- 2017/CSA B125.14-17 | Manually Operated Valves for Use in Plumbing Systems | 7.2.10.6 .(7) |
| ASME/CSA | ASME A112.18.1-2018 / CSA B125.1-18 | Plumbing Supply Fitti ngs | 7.2.10.6 .(1) 7.2.10.7 .(1) 7.2.10.7 B.(1) |
| ASME/CSA | ASME A112.18.2-2015 / CSA B125.2-15 | Plumbing Waste Fittings | 7.2.3.3.(1) 7.2.10.6 .(6) |
| ASME/CSA | ASME A112.18.6- 2017/CSA B125.6-17 | Flexible water connectors | 7.2.10.18 .(1) |
| ASME/CSA | ASME A112.19.1-2018 / CSA B45.2-18 | Enamelled Cast Iron and Enamelled Steel Plumbing Fixtures | 7.2.2.2.(1) |
| ASME/CSA | ASME A112.19.2-2018 / CSA B45.1-18 | Ceramic Plumbing Fixtures | 7.2.2.2.(1) |
| ASME/CSA | ASME A112.19.3-2017 / CSA B45.4-17 | Stainless Steel Plumbing Fixtures | 7.2.2.2.(1) |
| ASME/CSA | ASME A112.19.7-2012 / CSA B45.10-12 | Hydromassage Bathtub Systems | 7.2.2.2.(1) |
| ASPE | ASPE Plumbing Engineering Design Handbook - Volume 1 2021 | Fundamentals of Plumbing Engineering | 7.6.3.1.(2) 7.7.3.1.(1) |
| ASPE | ASPE Plumbing Engineering Design Handbook - Volume 2 2022 | Plumbing Systems | 7.6.3.1.(2) 7.7.3.1.(1) |
| ASPE | ASPE Plumbing Engineering Design Handbook -Volume 3 2023 | Special Plumbing Systems | 7.6.3.1.(2) 7.7.3.1.(1) |
| ASPE | ASPE Plumbing Engineering Design Handbook - Volume 4 2020 | Plumbing Components and Equipment | 7.6.3.1.(2) 7.7.3.1.(1) |
| ASSE | ANSI/ASSE 1010-2004 | Water Hammer Arresters | 7.2.10.15 .(1) |
| ASSE | 1051-2009 | Individual and Branch Type Ai r Admittance Valves for Sanitary Drainage Systems | 7.2.10.16 .(1) |
| ASSE/ASME/CSA | ASSE 1002-2015/ASME A112.1002-2015/CSA B125.12-15 | Anti-siphon fill valves for water closet tan ks | 7.2.10.10 .(2) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| ASSE/ASME/CSA | ASSE 1016-2017/ASME A112.1016-2017/CSA B125.16-17 | Performance Requirements for Automatic Compensating Valves for Individual Showers and Tub/ Shower Combinations | 7.2.10.7 .(1) |
| ASSE/ASME/CSA | ASSE 1037-2015/ASME A112.1037-2015/CSA B125.37-15 | Performance requirements for pressurized flushing devices for plumbing fixtures | 7.2.10.8 .(1) |
| ASSE/ASME/CSA | ASSE 1070-2015/ASME A112.1070-2015/CSA B125.70-15 | Performance requirements for water temperature li miting devices | 7.2.10.7 .(2) |
| ASTM | A53 / A53M-18 | Standard Specification fo r Pipe, Steel, Black and Hot-Dipped, Zinc- Coated Welded and Seamless | 7.2.6.7.(4) |
| ASTM | A123 / A123M-17 | Standard Specification fo r Zinc (Hot Dip Galvanized) Coatings on Iron and Steel Products | Table 5.9.1.1 . Table 9.20.16.1 . |
| ASTM | A153 / A153M-16a | Standard Specification for Zinc Coa ting (Hot-Dip) on Iron and Steel Hardware | Table 5.9.1.1 . Table 9.20.16.1 . 9.23.2.4 .(2) |
| ASTM | A182 / A182M-19 | Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves an d Parts for High- Temperature Service | 7.2.6.12 .(1) 7.2.6.13 .(1) |
| ASTM | A252-10 | Standard Specification for We lded and Seamless Steel Pipe Piles | 4.2.3.8.(1) |
| ASTM | A269-15a | Seamless and Welded Austenitic Stainless Steel Tubing for General Service | 7.2.6.14 .(1) |
| ASTM | A283 / A283M-18 | Standard Specification for Low and Int ermediate Tensile Strength Carbon Steel Plates | 4.2.3.8.(1) |
| ASTM | A312 / A312M-18a | Standard Specification for Seamless, Welded, and Heavily Cold Worked Stainless Steel Pipes | 7.2.6.10 .(1) |
| ASTM | A351 / A351M-18 | Standard Specification for Castings, Austenitic, for Pressure-Co ntaining Parts | 7.2.6.13 .(1) |
| ASTM | A403 / A403M-19 | Standard Specification for Wrought Austenitic S tainless Steel Piping Fittings | 7.2.6.11 .(1) |
| ASTM | A518 / A518M-99 | Standard Specification for Corros ion-Resistant High-Silicon Iron Castings | 7.2.8.1.(1) |
| ASTM | A653 / A653M-18 | Standard Specification for Steel Sheet, Zinc-Coated (G alvanized) or Zinc-Iron Alloy-Coat ed (Galvannealed) by the Hot-Dip Process | Table 5.9.1.1 . 9.3.3.2.(1) 9.23.2.4 .(1) |
| ASTM | A792 / A792M-10 | Standard Specification for Steel Sheet, 55% Aluminum-Zinc Alloy- Coated by the Hot-Dip Process | 9.3.3.2.(1) |
| ASTM | A1008 / A1008M-18 | Standard Specification for Steel, Sheet, Cold-Rolled, Car bon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improv ed Formability, Solution Hardened, and Bake Harden able | 4.2.3.8.(1) |
| ASTM | A1011 / A1011M-18a | Standard Specification for Steel, Sheet and Stri p, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength | 4.2.3.8.(1) |
| ASTM | B32-08 | Standard Specificati on for Solder Metal | 7.2.9.2.(1) |
| ASTM | B42-15a | Standard Specification for Seamless Coppe r Pipe, Standard Sizes | 7.2.7.1.(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| ASTM | B43-15 | Standard Specification for Seamless Red Brass Pipe, Standard Sizes | 7.2.7.1.(2) |
| ASTM | B68 / B68M-19 | Standard Specification for Seamless Copper Tube, Bright Annealed | 7.2.7.4.(4) |
| ASTM | B88-16 | Standard Specification for Seamless Copper Water Tube | 7.2.7.4.(1) 7.2.7.4.(4) Table 7.2.11.2 . |
| ASTM | B306-13 | Standard Specification for Co pper Drainage Tube (DWV) | 7.2.7.4.(1) |
| ASTM | B813-16 | Standard Specification fo r Liquid and Paste Fluxes for Soldering of Copper and Copper Al loy Tube | 7.2.9.2.(3) |
| ASTM | B828-16 | Standard Specification for Making Capillary J oints by Soldering of Copper and Copper A lloy Tube and Fittings | 7.3.2.4.(1) |
| ASTM | C4-04 | Standard Specification for Cl ay Drain Tile and Perforated Clay Drain Tile | Table 5.9.1.1 . 9.14.3.1 .(1) |
| ASTM | C27-98 | Standard Specification for Fireclay and High-Alumina Refractory Brick | 9.21.3.4 .(1) |
| ASTM | C73-17 | Standard Specification for Calcium Si licate Brick (Sand-Lime Brick) | Table 5.9.1.1 . 9.20.2.1 .(1) |
| ASTM | C126-13 | Standard Specification for Ceramic Glazed S tructural Clay Facing Tile, Facing Brick, and Solid Masonry Units | Table 5.9.1.1 . 9.20.2.1 .(1) |
| ASTM | C212-17 | Standard Specification for Structu ral Clay Facing Tile | Table 5.9.1.1 . 9.20.2.1 .(1) |
| ASTM | C260 / C260M-10a | Standard Specification for Air-Entraining Admixtures for Concrete | 9.3.1.8.(1) |
| ASTM | C411-19 | Standard Specification f or Hot-Surface Performance of High- Temperature Thermal Insulation | 3.6.5.4.(4) 3.6.5.5.(1) 9.33.8.2 .(2) |
| ASTM | C412M-15 | Standard Specification for Concre te Drain Tile (Metric) | Table 5.9.1.1 . 9.14.3.1 .(1) |
| ASTM | C444M-17 | Standard Specification for P erforated Concrete Pipe (Metric) | Table 5.9.1.1 . 9.14.3.1 .(1) |
| ASTM | C494 / C494M-17 | Standard Specification for Chemical Admixtures for C oncrete | 9.3.1.8.(1) |
| ASTM | C553-13 | Standard Specification for Mineral Fiber Blanket Thermal Insulation for Commercial and Industrial Applications | Table 5.9.1.1 . |
| ASTM | C612-14 | Standard Specification for Mineral Fiber Block and Board Thermal Insulation | Table 5.9.1.1 . |
| ASTM | C700-18 | Standard Specification for Vitrified Clay Pipe, Extra Strength, Standard Strength and Perforated | Table 5.9.1.1 . 9.14.3.1 .(1) |
| ASTM | C726-17 | Standard Specification for Mineral Wool Roof Insulation Board | Table 5.9.1.1 . 9.25.2.2 .(1) |
| ASTM | C834-17 | Standard Specification for Latex Sealants | Table 5.9.1.1 . 9.27.4.2 .(2) |
| ASTM | C840-18b | Standard Specification for Application and Fin ishing of Gypsum Board | 3.1.6.6.(6) Table 5.9.1.1 . 9.29.5.1 .(3) |
| ASTM | C920-18 | Standard Specification for Elast omeric Joint Sealants | Table 5.9.1.1 . 9.27.4.2 .(2) |
| ASTM | C954-18 | Standard Specification for Steel Drill Screws for t he Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness | 9.24.1.4 .(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| ASTM | C991-16 | Standard Specification for Flexible Fibrous Glass Insulation for Metal Buildings | Table 5.9.1.1 . |
| ASTM | C1002-07 | Standard Specification for Steel Self-Piercing Tapping Screw s for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs | Table 5.9.1.1 . 9.24.1.4 .(1) 9.29.5.7 .(1) |
| ASTM | C1053-00 | Standard Specification for Borosilicate Glass Pipe and Fittings for Drain, Waste and Vent (DWV) Applicat ions | 7.2.8.1.(1) |
| ASTM | C1177 / C1177M-17 | Standard Specification for Glass Mat Gypsum Substrate for Use as Sheathing | 3.1.5.14 .(6) 3.1.5.15 .(4) Table 5.9.1.1 . Table 9.23.17.2 -A |
| ASTM | C1178 / C1178M-18 | Standard Specification for Coated Glass Mat W ater-Resistant Gypsum Backing Panel | 3.1.5.14 .(6) 3.1.5.15 .(4) Table 5.9.1.1 . 9.29.5.2 .(1) |
| ASTM | C1184-18e1 | Standard Specification for Structural Silicone Sealants | Table 5.9.1.1 . 9.27.4.2 .(2) |
| ASTM | C1280-13 | Standard Specification for Application o f Exterior Gypsum Panel Products for Use as Sheathing | Table 5.9.1.1 . |
| ASTM | C1311-14 | Standard Specification for Solvent Release Sealants | Table 5.9.1.1 . 9.27.4.2 .(2) |
| ASTM | C1330-18 | Standard Specification for Cylindri cal Sealant Backing for Use with Cold Liquid-Applied Sealants | Table 5.9.1.1 . 9.27.4.2 .(3) |
| ASTM | C1396 / C1396M-17 | Standard Specificatio n for Gypsum Board | 3.1.5.14 .(6) 3.1.5.15 .(4) 3.1.6.6.(2) 3.1.6.6.(3) 3.1.6.6.(4) 3.1.6.6.(5) 3.1.6.15 .(1) Table 5.9.1.1 . Table 9.23.17.2 .-A 9.29.5.2 .(1) Table 9.29.5.3 . |
| ASTM | C1658 / C1658M-18 | Standard Specification for Glass Mat Gypsum Panels | 3.1.5.14 .(6) Table 5.9.1.1 . |
| ASTM | D323-15a | Standard Specification for Vapor Pre ssure of Petroleum Products (Reid Method) | 1.4.1.2.(1) of Division A |
| ASTM | D374-99 / D374M-16 | Standard Test Method s for Thickness of Solid Electrical Insulation | 3.15.4.1 .(1) |
| ASTM | D635-22 | Standard Test Method for Ra te of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Posi tion | 3.15.4.1 .(1) |
| ASTM | D1227 / D1227M-13 | Standard Specification for Emulsified Asphalt Used as a Protective Coating for Roofing | Table 5.9.1.1 . 9.13.2.2 .(2) 9.13.3.2 .(2) |
| ASTM | D2178 / D2178M-13a | Standard Specification for Asphalt Glass Felt Used in Roofing and Waterproofing | Table 5.9.1.1 . |
| ASTM | D2466-17 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40 | 7.2.5.7.(2) |
| ASTM | D2467-15 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80 | 7.2.5.7.(2) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| ASTM | D2898-10 | Standard Practice for Accelerated Weathering of Fire- Retardant-Treated Wood for Fire Testing | 3.1.4.8.(3) 3.1.5.5.(3) 3.1.5.24 .(1) 3.1.6.9.(8) 3.2.3.7.(4) |
| ASTM | D3019 / D3019M-17 | Standard Specification for Lap Cement Used with Asphalt Roll Roofing, Non-Fibered, Asbestos-Fibered, and Non-Asbesto s-Fibered | Table 5.9.1.1 . 9.13.3.2 .(2) Table 9.27.2.1 .-B |
| ASTM | D3261-16 | Standard Specification for Butt Heat Fusion Polyethylene (PE) Plas tic Fittings for Polyethylene (PE) Plastic Pipe and Tubing | 7.2.5.4.(3) |
| ASTM | D3679-17 | Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding | 9.27.12.1 .(1) |
| ASTM | D3801-20a | Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position | 3.15.4.1 .(1) |
| ASTM | D4477-16 | Standard Specification for Rigid (Un plasticized) Poly(Vinyl Chloride) (PVC) Soffit | 9.27.12.1 .(3) |
| ASTM | D4479 / D4479M-07e1 | Standard Specification for Asphalt Roof Coatin gs - Asbestos-Free | Table 5.9.1.1 . 9.13.2.2 .(2) 9.13.3.2 .(2) Table 9.26.2.1 .-B |
| ASTM | D4637 / D4637M-15 | Standard Specification for EPDM Sheet Used In Single-Ply Roof Membrane | Table 5.9.1.1 . 9.13.3.2 .(2) Table 9.26.2.1 .-B |
| ASTM | D4811 / D4811M-16 | Standard Specification for Nonvulcanized (Uncured) Rubber Sheet Used as Roof Flashing | Table 5.9.1.1. 9.13.3.2 .(2) Table 9.26.2.1 .-B |
| ASTM | D5456-19 | Standard Specification for Evaluation of Struct ural Composite Lumber Products | 3.1.11.7 .(5) |
| ASTM | D6878 / D6878M-11a | Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing | Table 5.9.1.1 . 9.13.3.2 .(2) Table 9.26.2.1 .-B |
| ASTM | D7254-17 | Standard Specification for Polypr opylene (PP) Siding | 9.27.13.1 .(1) |
| ASTM | D7793-17 | Standard Specification for Insulated Vinyl Siding | 9.27.12.1 .(2) |
| ASTM | E90-09 | Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements | 5.8.1.2.(1) 5.8.1.4.(1) 9.11.1.2 .(1) |
| ASTM | E96 / E96M-16 | Standard Test Methods for Water Vapor Tran smission of Materials | 5.5.1.2.(3) 9.13.2.2 .(2) 9.25.4.2 .(1) 9.25.4.2 .(2) 9.25.5.1 .(1) |
| ASTM | E283-04 | Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen | 5.9.3.4.(2) |
| ASTM | E331-00 | Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference | 5.9.3.5.(2) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| ASTM | E336-11 | Standard Test Method for Measureme nt of Airborne Sound Attenuation Between Rooms in Buildings | 5.8.1.2.(2) 5.8.1.4.(7) 9.11.1.2 .(2) |
| ASTM | E413-16 | Classification for Rating Sound Insulation | 5.8.1.2.(1) 5.8.1.2.(2) 5.8.1.4.(7) 5.8.1.5.(3) 9.11.1.2 .(1) 9.11.1.2 .(2) |
| ASTM | E547-00 | Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Cyclic Static Air Pressure Difference | 5.9.3.5.(2) |
| ASTM | E130016 | Standard Practice for Determining Load Resistance of G lass in Buildings | 4.3.6.1.(1) |
| ASTM | E2190-19 | Standard Specification for Insulating Glass Unit Performance and Evaluation | Table 5.9.1.1 . 9.6.1.2.(1) |
| ASTM | E2307-15b | Standard Test Method for Determining Fire Resistance of Perimeter Fire Barriers Using Intermediate-Scale, Multi-storey Test Apparatus | 3.1.8.3.(4) 9.10.9.2 .(4) |
| ASTM | F476-14 | Standard Test Methods for Secur ity of Swinging Door Assemblies | 9.7.5.2.(2) |
| ASTM | F628-12e2 | Standard Specification for Acrylonitrile-Butadiene-Styren e (ABS) Schedule 40 Plastic Drai n, Waste, and Vent Pipe With a Cellular Core | 7.2.5.9.(1) 7.2.5.11 .(1) 7.2.5.11 .(1.1) |
| ASTM | F714-13 | Standard Specificatio n for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter | 7.2.5.5.(1) |
| ASTM | F1667-18a | Standard Specification for Driven Fasteners: Nails, Spikes and Staples | 9.23.3.1 .(1) 9.26.2.3 .(1) 9.29.5.6 .(1) |
| ASTM | F3128-19 | Standard Specification for Poly(Vinyl Chlorid e) (PVC) Schedule 40 Drain, Waste, and Vent Pipe with a Cellular Core | 7.2.5.16 .(1) |
| AWS | ANSI/AWS A5.8M / A5 .8: 2011 | Specification for Filler Metals for Brazing and Braze Welding | 7.2.9.2.(4) |
| AWWA | ANSI/AWWA C104 / A21.4-13 | Cement-Mortar Lining for Ductile-Iron Pipe and Fittings | 7.2.6.4.(2) Table 7.2.11.2 . |
| AWWA | ANSI/AWWA C110 / A21.10-12 | Ductile-Iron and Gray-Iron Fittings | 7.2.6.4.(3) Table 7.2.11.2 . |
| AWWA | ANSI/AWWA C111 / A21.11-12 | Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings | 7.2.6.4.(4) Table 7.2.11.2 . |
| AWWA | ANSI/AWWA C151 / A21.51-09 | Ductile-Iron Pipe, Centrifugally Cast | 7.2.6.4.(1) Table 7.2.11.2 . |
| AWWA | ANSI/AWWA C228-08 | Stainless-Steel Pipe Fla nges For Water Service - Sizes 2 in. through 72 in. (50 mm through 1,800 mm) | 7.2.6.12 .(1) |
| BCMOH | Version 2, 21st Sept, 2007 | Sewerage System Standard Practice Manual | 8.7.8.3.(2) 8.7.8.3.(3) |
| BNQ | BNQ 3624-115-2016 | Polyethylene (PE) Pipe and Fittings - Flexible Pipes for Dra inage - Characteristics and Test Methods | Table 5.9.1.1 . 9.14.3.1 .(1) |
| BNQ | CAN/BNQ 3680-600- 2023 | Onsite Residential Wastewater Treatment Technologies | 8.6.2.2.(5) Table 8.6.2.2 . |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| CCBFC | NRCC 38726 1995 | National Building Code of Canada | 2.1.2.3.(3) 2.1.2.3.(5) |
| CCBFC | NRCC 38732 1995 | National Farm Building Code of Canada | 2.1.2.3.(1) 2.1.2.3.(2) 2.1.2.3.(3) 2.1.2.3.(5) |
| CCBFC | NRCC-CONST-56435E 2020 | National Building Code of Canada | 2.4.2.1.(2) of Division C |
| CCBFC | NRCC-CONST-56436E 2020 | National Plumbing Code of Canada | 2.4.2.1.(2) of Division C |
| CCBFC | NRCC-CONST-56437E 2020 | National Fire Code of Canada | 1.4.1.2.(1) of Division A 2.2.6.11 .(1) 2.2.8.1.(1) 2.2.8.1.(4) 2.2.8.7.(1) 2.4.2.3.(4) 3.1.13.1 .(1) 3.3.1.2.(1) 3.3.5.2.(1) 3.7.5.2.(1) 6.9.1.2.(1) |
| CGSB | CAN/CGSB-1.501-M89 | Method of Permeance of Coate d Wallboard | 5.5.1.2.(2) 9.25.4.2 .(7) |
| CGSB | CAN/CGSB-7.2-94 | Adjustable Steel Colu mns | 9.17.3.4 .(1) |
| CGSB | CAN/CGSB-10.3-92 | Air Setting Refractory Mortar | 9.21.3.4 .(2) 9.21.3.9 .(1) 9.22.2.2 .(2) |
| CGSB | CAN/CGSB-11.3-M87 | Hardboard | Table 5.9.1.1 . 9.29.7.1 .(1) 9.30.2.2 .(1) |
| CGSB | CAN/CGSB-12.1-2017 | Safety Glazing | 3.3.1.20 .(3) 3.3.2.17 .(1) 3.3.2.17 .(2) 3.4.6.15 .(1) 3.4.6.15 .(3) 3.7.4.10 .(1) Table 5.9.1.1 . 9.6.1.2.(1) 9.6.1.4.(1) 9.6.1.4.(6) 9.8.8.7.(1) |
| CGSB | CAN/CGSB-12.2-M91 | Flat, Clear Sheet Glass | Table 5.9.1.1 . 9.6.1.2.(1) |
| CGSB | CAN/CGSB-12.3-M91 | Flat, Clear Float Glass | Table 5.9.1.1 . 9.6.1.2.(1) |
| CGSB | CAN/CGSB-12.4-M91 | Heat Absorbing Glass | Table 5.9.1.1 . 9.6.1.2.(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| CGSB | CAN/CGSB-12.5-M86 | Mirrors, Silvered | 9.6.1.2.(3) |
| CGSB | CAN/CGSB-12.8-97 | Insulating Glass Units | Table 5.9.1.1 . 9.6.1.2.(1) |
| CGSB | CAN/CGSB-12.9-M91 | Spandrel Glass | Table 5.9.1.1 . 9.6.1.2.(1) |
| CGSB | CAN/CGSB-12.10-M76 | Glass, Light and Heat Reflecting | 9.6.1.2.(1) |
| CGSB | CAN/CGSB-12.11-M90 | Wired Safety Glass | 3.3.1.20 .(3) 3.4.6.15 .(1) 3.4.6.15 .(3) 9.6.1.2.(1) 9.6.1.4.(1) 9.8.8.7.(1) |
| CGSB | CAN/CGSB-12.20-M89 | Structural Design of Glass for Buildings | 4.3.6.1.(1) |
| CGSB | CAN/CGSB-19.22-M89 | Mildew Resistant Sealing Com pound for Tubs and Tiles | 9.29.10.5 .(1) |
| CGSB | 37-GP-9Ma-1983 | Primer, Asphalt, Unfilled, for Asphalt Roofing, Dampproofing and Waterproofing | Table 5.9.1.1 . 9.13.3.2 .(2) Table 9.26.2.1 .-A |
| CGSB | CAN/CGSB-37.50-M89 | Hot-Applied, Rubberiz ed Asphalt for Roofing and Waterproofing | Table 5.9.1.1 . 9.13.3.2 .(2) Table 9.26.2.1 .-B |
| CGSB | CAN/CGSB-37.51-M90 | Application for Hot-App lied Rubberized Asphalt for Roofing and Waterproofing | 9.26.15.1 .(1) |
| CGSB | CAN/CGSB-37.54-95 | Polyvinyl Chloride Roofing and Waterproofing Membrane | Table 5.9.1.1 . 9.13.3.2 .(2) Table 9.26.2.1 .-B |
| CGSB | 37-GP-55M-1979 | Application of Sheet App lied Flexible Polyvinyl Chloride Roofing Membrane | 9.26.16.1 .(1) |
| CGSB | 37-GP-56M-1985 | Membrane, Modified, Bituminous, Prefabricated, and Reinforced for Roofing | 9.13.3.2 .(2) Table 9.26.2.1 .-B |
| CGSB | CAN/CGSB-37.58-M86 | Membrane, Elastomeric, Cold-Applied Liquid, for Non-Exposed Use in Roofing and Waterproofing | Table 5.9.1.1 . 9.13.3.2 .(2) Table 9.26.2.1 .-B |
| CGSB | CAN/CGSB-51.25-M87 | Thermal Insulation, Phe nolic, Faced | Table 9.23.17.2 .-A 9.25.2.2 .(1) |
| CGSB | 51-GP-27M-1979 | Thermal Insulation, Polystyre ne, Loose Fill | 9.25.2.2 .(1) |
| CGSB | CAN/CGSB-51.32-M77 | Sheathing, Membrane, Breather Type | Table 5.9.1.1. 9.20.13.9.( 1) Table 9.26.2.1.-A 9.27.3.2.( 1) |
| CGSB | CAN/CGSB-51.33-M89 | Vapour Barrier, Sheet, Excluding Polyethylene, for Use in Building Construction | Table 5.9.1.1 . 9.25.4.2 .(5) |
| CGSB | CAN/CGSB-51.34-M86 | Vapour Barrier, Polyethylene Sheet for Use in Building Construction | Table 5.9.1.1 . 9.13.2.2 .(2) 9.13.4.2 .(1.2) 9.18.6.2 .(1) 9.25.3.2 .(2) 9.25.4.2 .(4) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| CGSB | CAN/CGSB-51.71-2005 | Depressurization Test | 9.32.3.8 .(7) |
| CGSB | CAN/CGSB-82.6-M86 | Doors, Mirrored Glass, Sliding or Folding, Wardrobe | 9.6.1.2.(2) |
| CGSB | CAN/CGSB-93.1-M85 | Sheet, Aluminum Alloy, Prefinished Residential | Table 5.9.1.1 . 9.27.11.1 .(3) |
| CGSB | CAN/CGSB-93.2-M91 | Prefinished Aluminum Siding, Soffits and Facsia for Residential Use | 3.2.3.6.(5) Table 5.9.1.1 . 9.10.14.5 .(12) 9.27.11.1 .(2) |
| CSA | CAN/CSA-6.19-01 | Residential carbon monoxide al arming devices | 6.9.4.4.(1) 9.32.3.9 .(2) 9.32.3.9 C.(1) |
| CSA | A23.1:19 | Concrete materials and methods of concr ete construction | 4.2.3.6.(1) 4.2.3.9.(1) Table 5.9.1.1 . 9.3.1.1.(1) 9.3.1.1.(4) 9.3.1.3.(1) 9.3.1.4.(1) 9.40.1.4 .(1) |
| CSA | A23.3:19 | Design of concrete structures | Table 4.1.8.9 . 4.1.8.18 .(7) 4.3.3.1.(1) |
| CSA | A60.1-M1976 | Vitrified Clay Pipe | 7.2.5.3.(1) |
| CSA | A60.3-M1976 | Vitrified Clay Pipe Joints | 7.2.5.3.(2) |
| CSA | CAN/CSA-A82-14 | Fire masonry brick made from clay or shale | Table 5.9.1.1 . 9.20.2.1 .(1) |
| CSA | CAN/CSA-A82.27-M91 | Gypsum Board | 3.1.5.14 .(6) 3.1.5.15 .(4) 3.1.6.6.(2) 3.1.6.6.(3) 3.1.6.6.(4) 3.1.6.6.(5) 3.1.6.15 .(1) 9.29.5.2 .(1) |
| CSA | A82.30-M1980 | Interior Furring, Lathing and Gypsum Plas tering | 9.29.4.1 .(1) |
| CSA | A82.31-M1980 | Gypsum Board Application | 3.2.3.6.(5) 9.10.9.2 .(5) 9.10.12.4 .(3) 9.10.14.5 .(12) 9.29.5.1 .(2) |
| CSA | CAN3-A93-M82 | Natural Airflow Ventilators for Buildings | Table 5.9.1.1 . 9.19.1.2 .(5) |
| CSA | CAN/CSA-A123.2-03 | Asphalt Coated Roofing Sheets | Table 5.9.1.1 . 9.13.3.2 .(2) Table 9.26.2.1 .-B |
| CSA | A123.3-05 | Asphalt Saturated Organic Roofing Felt | Table 5.9.1.1 . Table 9.26.2.1 .-B |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| CSA | CAN/CSA-A123.4-04 | Asphalt for Constructing Built-Up Roof Co verings and Waterproofing Systems | Table 5.9.1.1 . 9.13.2.2 .(2) 9.13.3.2 .(2) Table 9.26.2.1 .-B |
| CSA | A123.5:16 | Asphalt shingles made from glass felt and surfac ed with mineral granules | Table 5.9.1.1 . 9.13.3.2 .(2) Table 9.26.2.1 .-B |
| CSA | CAN/CSA-A123.16:04 | Asphalt-coated glass-base shee ts | Table 5.9.1.1 . Table 9.26.2.1 .-B |
| CSA | A123.17-05 | Asphalt Glass Felt Used in Roofing and Waterproofing | Table 5.9.1.1 . 9.13.3.2 .(2) Table 9.26.2.1 .-B |
| CSA | CAN/CSA-A123.21:14 | Standard test method for the dynamic wind uplift resistance of membrane-roofing systems | 5.2.2.2.(4) |
| CSA | A123.22-08 | Self-Adhering Polymer Modified Bituminous Sheet Materials Us ed as Steep Roofing Underlaym ent for Ice Dam Protection | Table 9.26.2.1 -.B |
| CSA | A123.23-15 | Product specification for polymer-modified bitumen sheet , prefabricated and reinforced | Table 5.9.1.1 . Table 9.26.2.1 .-B |
| CSA | A123.51-14 | Asphalt shingle application on roof slope s 1:6 and steeper | Table 5.9.1.1 . 9.26.1.3 .(1) |
| CSA | A165.1-14 | Concrete block masonry units | Table 5.9.1.1 . 9.15.2.2 .(1) 9.17.5.1 .(1) 9.20.2.1 .(1) 9.20.2.6 .(1) |
| CSA | A165.2-14 | Concrete brick masonry un its | Table 5.9.1.1 . 9.20.2.1 .(1) |
| CSA | A165.3-14 | Prefaced concrete masonry units | Table 5.9.1.1 . 9.20.2.1 .(1) |
| CSA | CAN/CSA-A179-14 | Mortar and Grout for Unit Ma sonry | Table 5.9.1.1 . 9.15.2.2 .(3) 9.20.3.1 .(1) |
| CSA | CAN/CSA-A220 Series-06 | Concrete Roof Tiles | Table 5.9.1.1 . Table 9.26.2.1 .-B 9.26.17.1 .(1) |
| CSA | A257.1:19 | Non-reinforced circular concrete culvert, storm drain, sewer pipe, and fittings | 7.2.5.2.(1) |
| CSA | A257.2:19 | Reinforced circular concrete culvert, storm drain, sewer pipe, and fittings | 7.2.5.2.(1) |
| CSA | A257.3:19 | Joints for circular concrete sewer and cu lvert pipe, manhole sections, and fittings using rubber gaskets | 7.2.5.2.(2) |
| CSA | A257.4:19 | Precast reinforced circular concret e manhole sections, catch basins, and fittings | 7.2.5.2.(5) |
| CSA | A277-16 | Procedure for certification of prefabricated bu ildings, modules, and panels | 9.1.1.9.(1) 1.12.1.1 .(1) of Division C 3.1.1.1.(2) of Division C 3.2.4.1.(3) of Division C |
| CSA | CAN/CSA-A324-M88 | Clay Flue Liners | 9.21.3.3 .(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| CSA | CAN/CSA-A371-14 | Masonry Construction for Buildings | Table 5.9.1.1 . 9.15.2.2 .(3) 9.20.3.2 .(7) 9.20.15.2 .(1) |
| CSA | CAN/CSA-A405-M87 | Design and Construction of Masonry Chimneys and Fireplaces | 9.21.3.5 .(1) 9.22.1.4 .(1) 9.22.5.2 .(2) |
| CSA | AAMA/WDMA/CSA 101/I.S.2/A440-17 | NAFS – North American Fen estration Standard/Specification for windows, doors, and skyligh ts | 5.9.2.2.(1) Table 9.7.3.3 . 9.7.4.1.(1) 9.7.4.2.(1) 9.7.5.1.(1) 9.7.5.3.(1) |
| CSA | A440S1:19 | Canadian Supplement t o AAMA/WDMA/CSA 101/I.S.2/A440-17, NAFS - North American Fenestration St andard/Specification for windows, doors, and skylights | 5.9.2.2.(1) 5.9.3.5.(3) 9.7.4.2.(1) 9.7.4.3.(1) |
| CSA | A440.2-14 | Fenestration Energy Per formance | 12.3.1.2 .(1) |
| CSA | A440.2:19 / A440.3:19 | Fenestration Energy Perform ance / user Guide to CSA A440.2-14, Fenestration energy performance | Table 9.7.3.3 . |
| CSA | CAN/CSA-A440.4:19 | Window, door, and skyligh t installation | 9.7.6.1.(1) |
| CSA | A660-10 | Certification of manufacturers of steel buildi ng systems | 4.3.4.3.(1) |
| CSA | A3001-18 | Cementitious Materials for Use in Concrete | Table 5.9.1.1 . 9.3.1.2.(1) 9.28.2.1 .(1) |
| CSA | B52:23 | Mechanical refrigeration code | 6.3.1.5.(4) |
| CSA | B64.0-11 | Definitions, general requirements, and test methods for vacuum breakers and backflow preventers | 7.2.10.10 .(1) |
| CSA | B64.1.1-11 | Atmospheric vacuum breakers (AVB) | 7.2.10.10 .(1) |
| CSA | B64.1.2-11 | Pressure vacuum breakers (PVB) | 7.2.10.10 .(1) |
| CSA | B64.1.3-11 | Spill-resistant pressure vacuum breaker s (SRPVB) | 7.2.10.10 .(1) |
| CSA | B64.1.4-11 | Vacuum breaker, air spac e type (ASVB) | 7.2.10.10 .(1) |
| CSA | B64.2-11 | Hose connection vacuum breakers (HCVB) | 7.2.10.10 .(1) |
| CSA | B64.2.1-11 | Hose connection vacuum breakers (HCVB) with ma nual draining feature | 7.2.10.10 .(1) |
| CSA | B 64.2.1.1 -11 | Hose connection dual che ck vacuum breakers (HCDVB) | 7.2.10.10 .(1) |
| CSA | B64.2.2-11 | Hose connection vacuum breakers (hcvb) with aut omatic draining feature | 7.2.10.10 .(1) |
| CSA | B64.3-11 | Dual check valve backflow preventers with atmospheric port (DCAP) | 7.2.10.10 .(1) 7.6.2.5A.(4) |
| CSA | B64.3.1-11 | Dual check valve backflow preventer s with atmospheric port for carbonators (DCAPC) | 7.2.10.10 .(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| CSA | B64.4-11 | Reduced Pressure Principle (RP) backflow preventers | 7.2.10.10 .(1) 7.6.2.4.(2) |
| CSA | B64.4.1-11 | Reduced pressure principle backflow pr eventers for fire protection systems (RPF) | 7.2.10.10 .(1) 7.6.2.4.(2) 7.6.2.4.(4) |
| CSA | B64.5-11 | Double check valve (DCVA) backflow preventers | 7.2.10.10 .(1) 7.6.2.4.(2) |
| CSA | B64.5.1-11 | Double check valve backflow preventers for fire protection systems (DCVAF) | 7.2.10.10 .(1) 7.6.2.4.(2) |
| CSA | B64.6-11 | Dual check valve (DuC) backflow preventers | 7.2.10.10 .(1) 7.6.2.4.(2) 7.6.2.6.(3) 7.7.1.1.(6) |
| CSA | B64.6.1-11 | Dual check valve backflow preventers for fire protection systems (DuCF) | 7.2.10.10 .(1) 7.6.4.2.(2) |
| CSA | B64.7-11 | Laboratory faucet vacuum breakers (LFVB) | 7.2.10.10 .(1) |
| CSA | B64.8-11 | Dual check valve backflow preventers with intermediate vent (DuCV) | 7.2.10.10 .(1) |
| CSA | B64.9-11 | Single check valve backflow preventers for f ire protection systems (SCVAF) | 7.2.10.10 .(1) 7.6.2.4.(2) |
| CSA | B64.10-17 | Selection and installation of backflow preventers | 7.2.10.10 .(1) 7.6.2.3.(1) 7.6.2.6.(1) |
| CSA | B66-21 | Design, material, and manufactur ing requirements for prefabricated septic tanks and sewa ge holding tanks | 8.2.2.2.(1) 8.2.2.2.(2) 8.2.2.3.(7) 8.2.2.3.(11) |
| CSA | B70-12 | Cast iron soil pipe, fitti ngs and means of joining | 7.2.6.1.(1) 7.4.6.4.(2) |
| CSA | B70.1-03 | Frames and Covers for Maintenance Holes and Catchbasins | 7.2.6.2.(1) |
| CSA | B111-1974 | Wire Nails, Spikes and Staples | 9.23.3.1 .(1) 9.26.2.3 .(1) 9.29.5.6 .(1) |
| CSA | B125.3-18 | Plumbing fittings | 7.2.10.6 .(1) 7.2.10.7 .(2) 7.2.10.7 .(3) 7.2.10.7 B.(2) |
| CSA | CAN/CSA-B126.0-13 | General requirements and methods of testing for wat er cisterns | 7.7.2.4.(6) |
| CSA | CAN/CSA-B126.1-13 | Installation of water cisterns | 7.7.2.4.(6) |
| CSA | CAN/CSA-B127.3-18 | Fibrocement drain, waste, and vent pipe and pipe fittings | 7.2.5.1.(1) |
| CSA | CAN/CSA-B128.1-06 | Design and installation of non-potable water systems | 7.7.1.2.(1) 7.7.3.1.(1) |
| CSA | B137.1-17 | Polyethylene (PE) pipe, tubing and fittings for cold water pressure services | 7.2.5.4.(1) Table 7.2.11.2 . |
| CSA | B137.2-17 | Polyvinylchloride (PVC) injection-moulded gasketed fittings for pressure applications | 7.2.5.7.(3) 7.2.5.9.(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| CSA | B137.3-17 | Rigid polyvinylchloride (PVC) pipe and fitti ngs for pressure applications | 7.2.5.7.(1) 7.2.5.9.(1) Table 7.2.11.2 . |
| CSA | B137.5-17 | Crosslinked polyethylene (PEX) tubing s ystems for pressure applications | 7.2.5.6.(1) Table 7.2.11.2 . |
| CSA | B137.6-17 | Chlorinated polyvinylchloride (CPVC) pipe , tubing, and fittings for hot- and cold-water distribution systems | 7.2.5.8.(1) Table 7.2.11.2 . |
| CSA | B137.9-17 | Polyethylene/aluminum/polyethylene (PE-AL-PE ) composite pressure- pipe systems | 7.2.5.12 .(1) Table 7.2.11.2 . |
| CSA | B137.10-17 | Crosslinked polyethylene/aluminum crosslinked po lyethylene (PEX-AL-PEX) composite pressure-pip e systems | 7.2.5.12 .(4) 7.2.5.13 .(1) Table 7.2.11.2 . |
| CSA | B137.11-17 | Polypropylene (PP-R) pipe and fittings for pressure applications | 7.2.5.14 .(1) |
| CSA | B137.18-17 | Polyethylene of raised temperature resistance (PE-RT) tu bing systems for pressure applicatio ns | 7.2.5.15 .(1) |
| CSA | B158.1-1976 | Cast Brass Solder Joint Drainage, Waste and Vent Fittings | 7.2.10.1 .(1) |
| CSA | B181.1-18 | Acrylonitrile-butadiene-styrene (ABS) drain, waste, and vent pipe and pipe fittings | 7.2.5.9.(1) 7.2.5.10 .(1) 7.2.5.11 .(1) 7.2.5.11 .(1.1) 7.2.10.1 .(2) 7.4.6.4.(2) |
| CSA | B181.2-18 | Polyvinylchloride (PVC) and chlorinated polyvinylc hloride (CPVC) drain, waste, and vent pipe and pipe fittings | 7.2.5.9.(1) 7.2.5.10 .(1) 7.2.5.11 .(1) 7.2.5.11 .(1.1) 7.2.5.16 .(1) 7.2.5.16 .(2) 7.2.10.1 .(3) 7.4.6.4.(2) |
| CSA | B181.3-18 | Polyolefin and polyvinylidene fluoride ( PVDF) laboratory drainage systems | 7.2.8.1.(1) |
| CSA | B182.1-18 | Plastic drain and sewer pipe and pipe fittings | Table 5.9.1.1 . 7.2.5.9.(1) 7.2.5.11 .(1.1) 7.4.6.4.(2) 9.14.3.1 .(1) |
| CSA | B182.2-18 | PSM type polyvinylchloride (PVC) sewer pipe and fittings | 7.2.5.9.(1) 7.2.5.11 .(1.1) |
| CSA | B182.4-18 | Profile polyvinylchloride (PVC) sewer pipe and fittings | 7.2.5.9.(1) |
| CSA | B182.6-18 | Profile polyethylene (PE) sewer pipe and fittin gs for leak-proof sewer applications | 7.2.5.9.(1) |
| CSA | B182.8-18 | Profile polyethylene (PE) storm se wer and drainage pipe and fittings | 7.2.5.9.(1) |
| CSA | B214-16 | Installation code for hydronic heating systems | 6.2.1.1.(1) 6.2.1.5.(6) 9.33.4.2 .(1) |
| CSA | B242-05 | Groove- and Shoulder-Type Mechanical Pipe Couplings | 7.2.10.4 .(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| CSA | B272-93 | Prefabricated Self-Sealing Roof Vent Flashings | 7.2.10.14 .(2) |
| CSA | B355:19 | Platform lifts and st air lifts for barrier-free access | 3.8.3.5.(1) |
| CSA | CAN/CSA-B356-10 | Water pressure reducing valves for domestic water supply systems | 7.2.10.12 .(1) |
| CSA | B365-17 | Installation code for solid-fuel-burning applia nces and equipment | 6.2.1.5.(1) 6.2.1.5.(5) 9.21.1.4 .(1) 9.22.10.2 .(1) 9.33.5.3 .(1) |
| CSA | B366.1-11 | Solid-Fuel-Fired Centr al Heating Appliances | 6.2.1.5.(2) |
| CSA | B415.1-10 | Performance Testing of Solid-Fuel-B urning Heating Appliances | 6.2.1.5.(7) 9.33.5.3 .(2) |
| CSA | B481.0-12 | Material, design, and construction requirements f or grease interceptors | 7.2.3.2.(3) |
| CSA | B481.1-12 | Testing and Rating of Grease Interceptors Using L ard | 7.2.3.2.(4) 8.1.3.1.(8) |
| CSA | B481.2-12 | Testing and Rating of Grease Interceptors Using Oil | 7.2.3.2.(4) 8.1.3.1.(8) |
| CSA | B481.3-12 | Sizing, Selection, Location, and Installation of Grease Interceptors | 7.2.3.2.(3) |
| CSA | B481.4-12 | Maintenance of Grease Interceptors | 8.9.3.3.(1) |
| CSA | B365-17 | Installation code for solid-fuel-burning applia nces and equipment | 6.2.1.5.(1) 6.2.1.5.(5) 9.21.1.4 .(1) 9.22.10.2 .(1) 9.33.5.3 .(1) |
| CSA | B366.1-11 | Solid-Fuel-Fired Centr al Heating Appliances | 6.2.1.5.(2) |
| CSA | B415.1-10 | Performance Testing of Solid-Fuel-B urning Heating Appliances | 6.2.1.5.(7) 9.33.5.3 .(2) |
| CSA | B481.0-12 | Material, design, and construction requirements for grease interceptors | 7.2.3.2.(3) |
| CSA | B481.1-12 | Testing and Rating of Grease Interceptors Using L ard | 7.2.3.2.(4) 8.1.3.1.(8) |
| CSA | B481.2-12 | Testing and Rating of Grease Interceptors Using Oil | 7.2.3.2.(4) 8.1.3.1.(8) |
| CSA | B481.3-12 | Sizing, Selection, Location, and Installation of Grease Interceptors | 7.2.3.2.(3) |
| CSA | B481.4-12 | Maintenance of Grease Interceptors | 8.9.3.3.(1) |
| CSA | CAN/CSA-B483.1-07 | Drinking Water Treatment Systems | 7.2.10.17 .(1) |
| CSA | B602-16 | Mechanical couplings for drain, waste, a nd vent pipe and sewer pipe | 7.2.10.4 .(2) |
| CSA | B651-18 | Accessible design for the built enviro nment | 3.8.3.1.(7) 3.8.3.1.(8) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| CSA | C22.2 No. 0.3-09 | Test methods for electrical wires and cables | 3.1.4.3.(1) 3.1.4.3.(3) 3.1.5.21 .(1) 3.1.5.21 .(3) 3.1.5.25 .(1) 3.1.5.25 .(2) 9.34.1.5 .(1) |
| CSA | C22.2 No.113-10 | Fans and Ventilators | 9.32.3.10 .(7) |
| CSA | C22.2 No. 141:15 | Emergency lighting equipment | 3.2.7.4.(2) 3.4.5.1.(3) 9.9.11.3 .(3) 9.9.12.3 .(7) |
| CSA | C22.2 No. 211.0-03 | General Requirements a nd Methods of Testing for Nonmetallic Conduit | 3.1.5.23 .(1) |
| CSA | CAN/CSA-C22.2 No. 262-04 | Optical Fiber Cable and Communication Cable Raceway Systems | 3.1.5.23 .(1) |
| CSA | CAN/CSA-C22.3 No. 1-20 | Overhead Systems | 3.1.20.1 .(2) |
| CSA | CAN/CSA-C88-M90 | Power Transformers and Reactors | 3.6.2.7.(10) |
| CSA | CAN/CSA-C260-M90 | Rating for the Performance of Residential Mechanical Ventilating Equipment | 9.32.3.10 .(1) 9.32.3.10 .(2) Table 9.32.3.10 .-B |
| CSA | C282-15 | Emergency electrical powe r supply for buildings | 3.2.7.5.(1) |
| CSA | CAN/CSA-C439-09 | Standard laboratory methods of test for rat ing the performance of heat/energy-recovery ven tilators | 9.32.3.10 .(4) 9.32.3.10 .(5) |
| CSA | CAN/CSA-C448.1-13 | Design and Installation of Earth Energy Systems for Commercial and Institutional Buildings | 6.2.1.5.(4) 9.33.5.2 .(2) |
| CSA | CAN/CSA-C448.2-13 | Design and Installation of Earth Energy Systems for Residential and Other Small Buildings | 6.2.1.5.(3) 9.33.5.2 .(1) |
| CSA | F280-12 | Determining the required capacity o f residential space heating and cooling appliances | 9.33.4.1 .(1) 9.33.5.1 .(3) |
| CSA | CAN/CSA-F326-M91 | Residential Mechanical Ventilation Systems | 9.32.3.1 .(1) 9.33.4.1 .(1) |
| CSA | CAN/CSA- F379 Series-09 (excluding Supplement F379S1-11) | Packaged solar domestic hot water systems ( liquid-to-liquid heat transfer) | 7.2.10.13 .(1) |
| CSA | CAN/CSA- F379.1-09 | Packaged solar domestic hot water systems ( liquid-to-liquid heat transfer) for All Season Use | 7.6.1.8.(1) 7.6.2.5A.(3) 7.6.2.5A.(4) |
| CSA | CAN/CSA-F383-08 | Installation of packaged solar domestic hot water systems | 7.6.1.8.(1) |
| CSA | G30.18-09 | Carbon steel bars for co ncrete reinforcement | 9.3.1.1.(4) 9.40.1.3 .(1) |
| CSA | G40.21-13 | Structural quality steel | 4.2.3.8.(1) Table 5.9.1.1 . 9.23.4.3 .(2) |
| CSA | CAN/CSA-G164-M92 | Hot Dip Galvanizing of Irregularly Shaped Articles | 4.4.5.1.(4) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| CSA | CAN/CSA-G401-14 | Corrugated steel pipe products | Table 5.9.1.1 . 7.2.6.8.(1) 9.14.3.1 .(1) |
| CSA | CAN/CSA-O80 Series-15 | Wood preservation | 3.1.4.5.(1) 4.2.3.2.(1) Table 5.9.1.1 . |
| CSA | CAN/CSA-O80.0-15 | General requirements for wood pre servation | 4.2.3.2.(2) |
| CSA | CAN/CSA-O80.1-15 | Specification of tr eated wood | 4.2.3.2.(1) 9.3.2.9.(5) |
| CSA | CAN/CSA-O80.2-15 | Processing and treatment | 4.2.3.2.(1) |
| CSA | CAN/CSA-O80.3-15 | Preservative formulations | 4.2.3.2.(1) |
| CSA | O86:19 | Engineering design in wood | Table 4.1.8.9 . 4.3.1.1.(1) |
| CSA | O118.1-08 | Western Red Cedar Shakes and Shingles | Table 5.9.1.1 . Table 9.26.2.1 .-B 9.27.7.1 .(1) |
| CSA | O118.2-08 | Eastern White Cedar Shingles | Table 5.9.1.1 . Table 9.26.2.1 .-B 9.27.7.1 .(1) |
| CSA | O121-17 | Douglas fir plywood | Table 5.9.1.1 . Table 9.23.12.3 .-A Table 9.23.12.3 .-B Table 9.23.12.3 .-C Table 9.23.17.2 .-A 9.23.15.2 .(1) 9.23.16.2 .(1) 9.27.8.1 .(1) 9.30.2.2 .(1) |
| CSA | CAN/CSA-O122-16 | Structural glued-laminate d timber | Table 9.23.4.2 .-K Table 9.23.12.3 .-D |
| CSA | CAN/CSA-O132.2 Series-90 | Wood Flush Doors | 9.7.4.3.(4) |
| CSA | O141:05 | Softwood Lumber | Table 5.9.1.1 . 9.3.2.6.(1) |
| CSA | O151-17 | Canadian softwood plywood | Table 5.9.1.1 . Table 9.23.12.3 .-A Table 9.23.12.3 .-B Table 9.23.12.3 .-C 9.23.15.2 .(1) 9.23.16.2 .(1) Table 9.23.17.2 .-A 9.27.8.1 .(1) 9.30.2.2 .(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| CSA | O153-13 | Poplar plywood | Table 5.9.1.1 . 9.23.15.2 .(1) 9.23.16.2 .(1) Table 9.23.17.2 .-A 9.27.8.1 .(1) 9.30.2.2 .(1) |
| CSA | O177-06 | Qualification Code for Manufacturers of Structural Glued-Laminated Timber | 4.3.1.2.(1) Table 9.23.4.2 .-K Table 9.23.12.3 .-D |
| CSA | O325-16 | Construction sheathing | Table 5.9.1.1 . Table 9.23.12.3 .-A Table 9.23.12.3 .-B Table 9.23.12.3 .-C Table 9.23.13.6 . 9.23.15.2 .(1) 9.23.15.4 .(2) 9.23.16.2 .(1) 9.23.16.3 .(2) Table 9.23.16.7 .-B Table 9.23.17.2 .-A Table 9.23.17.2 .-B 9.29.9.1 .(2) 9.29.9.2 .(5) |
| CSA | O437.0-93 | OSB and Waferboard | Table 5.9.1.1 . Table 9.23.12.3 .-A Table 9.23.12.3 .-B Table 9.23.12.3 .-C 9.23.15.2 .(1) 9.23.15.4 .(2) 9.23.16.2 .(1) 9.23.16.3 .(2) Table 9.23.17.2 .-A 9.27.10.1 .(1) 9.29.9.1 .(2) 9.30.2.2 .(1) |
| CSA | S16-19 | Design of Steel Structures | Table 4.1.8.9 . 4.3.4.1.(1) |
| CSA | S37-18 | Antennas, Towers, and Antenna-Supporting Structures | 4.1.6.15 .(1) 4.1.7.11 .(1) |
| CSA | S136-16 | North American specification for the design of c old formed steel structural members (using the Appendix B prov isions applicable to Canada) | 4.1.8.1.(5) Table 4.1.8.9 . 4.3.4.2.(1) |
| CSA | S157-17 / S157.1-17 | Strength design in aluminum / Commentary on CSA S157-17, Strength design in aluminum | 4.3.5.1.(1) |
| CSA | S304-14 | Design of masonry structures | Table 4.1.8.9 . 4.3.2.1.(1) |
| CSA | S367-12 | Air-, cable-, and frame-supported membrane structur es | 4.4.1.1.(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| CSA | S406-16 | Specification of permanent wood foundations for housi ng and small buildings | 9.13.2.7 .(1) 9.15.2.4 .(1) 9.16.5.1 .(1) |
| CSA | S413-14 | Parking structures | 4.4.2.1.(1) |
| CSA | S478-19 | Durability in buildings | 5.1.4.2.(3) Table 5.9.1.1 . |
| CSA | Z32-15 | Electrical safety and essential electrical syste ms in health care facilities | 3.2.7.3.(4) 3.2.7.6.(1) 3.7.5.1.(1) |
| CSA | Z240 MH Series-16 | Manufactured homes | 3.1.1.1.(2) of Division C 3.2.4.1.(3) of Division C |
| CSA | Z240.2.1-16 | Structural requirements f or manufactured homes | 9.1.1.9.(1) 9.12.2.2 .(6) 9.15.1.3 .(1) |
| CSA | Z240.10.1-19 | Site preparation, foundation, and installatio n of buildings | 9.15.1.3 .(1) 9.23.6.3 .(1) |
| CSA | CAN/CSA-Z241 Series-18 | Park model trailers | 9.39.1.1 .(1) 9.39.2.1 .(1) 3.1.1.1.(2) of Division C 3.2.4.1.(3) of Division C |
| CSA | CSA Z271:20 | Design of suspended ac cess equipment | 4.4.5.1.(2) |
| CSA | CAN/CSA-Z317.2-15 | Special requirements for heating, ventilation and a ir conditioning (HVAC) systems in health care facilities | 6.2.1.1.(1) 6.2.3.15 .(6) |
| CSA | CAN/CSA-Z662-15 | Oil and gas pipeline systems | 3.2.3.22 .(1) |
| CSA | Z7396.1-17 | Medical gas piping systems - Part 1: Pipelines for medical gase s, medical vacuum, medical support gases , and anaesthetic gas scavenging systems | 3.7.5.2.(1) |
| CSA / IAPMO | CSA B45.5-17 / IAPMO Z124-2017 | Plastic plumbing fixtures | 7.2.2.2.(1) |
| CSA / ICC | CSA B805-18 / ICC 805-2018 | Rainwater harvesting systems | 7.7.2.4.(4) |
| CSSBI | 23M-2016 | Standard for Residen tial Steel Cladding | 9.27.11.1 .(1) |
| CWC | 2014 | Engineering Guide for Wood Frame Construction | 9.4.1.1.(1) 9.23.13.1 .(2) 9.23.13.2 .(2) 9.23.13.3 .(2) |
| DBR | Technical Paper No. 19 4, May 1965 | Fire Endurance of Protected Steel Columns and Beams | Table 11.5.1.1 .-A Table 11.5.1.1 .-B Table 11.5.1.1 .-C Table 11.5.1.1.-D/E Table 11.5.1.1 .-F |
| DBR | Technical Paper No. 207, October 1965 | Fire Endurance of Unit Masonry Wa lls | Table 11.5.1.1 .-A Table 11.5.1.1 .-B Table 11.5.1.1 .-C Table 11.5.1.1.-D/E Table 11.5.1.1 .-F |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| DBR | Technical Paper No. 222, June 1966 | Fire Endurance of Ligh t-Framed and Miscellaneous Assemblies | Table 11.5.1.1 .-A Table 11.5.1.1 .-B Table 11.5.1.1 .-C Table 11.5.1.1.-D/E Table 11.5.1.1 .-F |
| EPA | 625/R-92/016 (1994) | Radon Prevention in the Design and Construction of Schools and Other Large Buildings | 6.2.1.1.(1) |
| FINA | 2021 | Rules and Regulations - FINA Facilities Rule s 2021-2025 - FR3 Diving | 3.11.4.1 .(17) |
| HC | SOR/2015-17 | Hazardous Products Regulations | 1.4.1.2.(1) of Division A |
| HI | 2005 | Hydronics Institute Manuals | 6.2.1.1.(1) 9.32.2.3 .(4) 9.32.3.2 .(1) 9.33.4.1 .(1) 9.33.6.7 .(2) |
| HPVA | ANSI/HPVA HP-1-2009 | American National Standard for Hardwood and Decorative Plywood | Table 5.9.1.1 . 9.27.8.1 .(1) 9.30.2.2 .(1) |
| HRAI | 2017 Edition | HRAI Digest | 6.2.1.1.(1) 9.32.2.3 .(4) 9.32.3.2 .(1) 9.33.4.1 .(1) |
| HUD | Rehabilitation Guidelines 2000 | Guideline on Fire Ratings of Archaic Materials and Assemblies | Table 11.5.1.1 .-A Table 11.5.1.1 .-B Table 11.5.1.1 .-C Table 11.5.1.1.-D/E Table 11.5.1.1 .-F |
| HVI | HVI 915-2013 | Loudness Testing and Rating Procedure | 9.32.3.10 .(2) Table 9.32.3.10 .-B |
| HVI | HVI 916-2013 | Airflow Test Procedure | 9.32.3.10 .(1) |
| IAPMO | PS 63-2014 | Plastic Leaching Chambers | 8.7.2.3.(3) |
| ISO | 3864-1:2011 | Graphical symbols – Safety colours and safety signs – Part 1: Design principles for safety si gns and safety markings | 3.4.5.1.(2) 9.9.11.3 .(2) |
| ISO | 7010:2011 | Graphical symbols - Safety col ours and safety signs - Registered safety signs | 3.4.5.1.(2) 9.9.11.3 .(2) |
| ISO | 8201:2017 | Acoustics - audible emergency evacuation sig nal | 3.2.4.18 .(2) |
| ISO | 10848-1:2017 | Acoustics - Laboratory measurement of the fl anking transmission of airborne and impact sound between adjoining rooms | 5.8.1.4.(2) 5.8.1.4.(3) 5.8.1.5.(2) 5.8.1.5.(3) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| ISO | 15712-1:2005 | Building acoustics - Estimation of acoustic performance of buildings from the performance of elements - Part 1: Airborne sound insulation between rooms | 5.8.1.4.(1) 5.8.1.4.(2) 5.8.1.4.(4) 5.8.1.4.(5) 5.8.1.4.(6) 5.8.1.5.(1) 5.8.1.5.(2) 5.8.1.5.(5) 5.8.1.5.(6) |
| ISO | 23599:2019 | Assistive products for blind and vision-impaired persons – Tactile walking surface indicators | 3.8.3.18 .(1) |
| MMAH | Supplementary Standard SA-1, September 9, 2024 | Objectives and Functional Statements Attr ibuted to the Acceptable Solutions | 1.2.1.1.(1) of Division A 1.2.1.1.(2) of Division A |
| MMAH | Supplementary Standard SB-1, January 1, 2024 | Climatic and Seismic Data | 1.1.2.1.(1) 1.1.2.1.(2) 2.1.2.3.(4) 2.1.2.3.(5) 3.2.6.2.(2) 3.2.8.4.(1) 3.3.1.7.(1) 5.2.1.1.(1) 5.2.1.1.(2) 6.2.1.2.(1) 7.4.10.4 .(1) 9.4.1.1.(3) 9.4.2.2.(1) Tables 9.6.1.3 .-A to 9.6.1.3.-G Table 9.32.3.4 . 9.33.3.2 .(1) 9.33.4.1 .(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| MMAH | Supplementary Standard SB-2, January 1, 2024 | Fire Performance Ratings | 2.2.1.10 .(2) 3.1.4.8.(4) 3.1.5.5.(4) 3.1.5.6.(2) 3.1.5.29 .(1) 3.1.6.9.(6) 3.1.6.10 .(2) 3.1.7.1.(2) 3.1.8.16 .(2) 3.1.9.5.(1) 3.1.12.1 .(3) 3.2.3.12 .(1) 3.2.3.13 .(4) 3.6.1.5.(1) 3.13.2.1 .(11) 3.13.3.5 .(1) 3.13.3.6 .(2) 3.13.4.2 .(7) 9.10.3.1 .(1) 9.10.3.2 .(1) 9.10.5.1 .(3) 9.10.9.11 .(1) |
| MMAH | Supplementary Standard SB-3, January 1, 2024 | Fire and Sound Resistance Tables | 5.8.1.3.(1) 5.8.1.3.(2) 9.10.3.1 .(1) 9.10.5.1 .(3) 9.11.1.3 .(1) 9.11.1.3 .(2) Table 9.11.1.4 . 9.29.5.9 .(5) |
| MMAH | Supplementary Standard SB-4, January 1, 2024 | Measures for Fire Safe ty in High Buildings | 3.2.6.2.(1) 3.2.6.2.(7) 3.2.6.5.(3) 3.2.6.9.(1) 3.13.3.6 .(5) Table 11.5.1.1 .-C Table 11.5.1.1.-D/E Table 11.5.1.1 .-F |
| MMAH | Supplementary Standard SB-6, January 1, 2024 | Percolation Times and Soil Descriptions | 8.2.1.2.(2) |
| MMAH | Supplementary Standard SB-7, January 1, 2024 | Guards for Housing and Small Buildings | 9.8.8.2.(6) |
| MMAH | Supplementary Standard SB-8, January 1, 2024 | Design, Construction and In stallation of Anchorage Systems for Fixed Access Ladders | 3.6.1.6.(1) |
| MMAH | Supplementary Standard SB-9, January 1, 2024 | Requirements for Soil Gas Control | 9.13.4.1 .(3) 9.13.4.2 .(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| MMA | Supplementary Standard SB-10, December 22, 2016 | Energy Efficiency Requirements | Table 9.7.3.3 . 12.2.1.2 .(2) 12.2.2.1 .(1) 12.2.3.1 .(1) |
| MMAH | Supplementary Standard SB-11, January 1, 2024 | Construction of Farm Buildings | 2.1.2.3.(5) |
| MMA | Supplementary Standard SB-12, July 7, 2016 | Energy Efficiency for Housing | Table 9.7.3.3 . Table 11.5.1.1 .-C 12.2.1.2 .(3) |
| MMAH | Supplementary Standard SB-13, January 1, 2024 | Glass in Guards | 3.1.21.1 .(1) |
| MMAH | Supplementary Standard SC-1, January 1, 2024 | Code of Conduct for Regi stered Code Agencies | 3.7.4.1.(2) of Division C |
| MOE | PIBS 6879 2008 | Design Guidelines for Sewage Works | 7.1.2.5.(1) |
| MOE | PIBS 6881e 2008 | Design Guidelines fo r Drinking-Water Systems | 7.1.2.5.(2) |
| NFPA | 2023 Publication | National Fire Codes | 6.2.1.1.(1) |
| NFPA | 13-2019 | Standard for the Installatio n of Sprinkler Systems | 3.1.9.1.(4) 3.2.4.8.(2) 3.2.4.15 .(1) 3.2.5.12 .(1) 3.2.5.12 .(9) 3.2.8.2.(5) 3.2.8.3.(2) 3.3.2.14 .(3) 3.16.1.1 .(3) 3.16.1.1 .(4) 3.16.1.6 .(2) 3.16.1.6 .(8) 3.16.1.7 .(2) 3.16.2.1 .(1) 3.16.2.2 .(1) 3.16.3.1 .(1) 9.10.9.9 .(4) |
| NFPA | 13D-2016 | Standard for the Installation of Sp rinkler Systems in One- and Two- Family Dwellings and Ma nufactured Homes | 3.2.4.1.(2) 3.2.5.12 .(3) 3.2.7.9.(4) |
| NFPA | 13R-2019 | Standard for the Ins tallation of Sprinkler Systems in Low-Rise Residential Occupancies | 3.2.5.12 .(2) |
| NFPA | 14-2013 | Standard for the Installa tion of Standpipe and Hose Systems | 3.2.5.9.(1) 3.2.5.10 .(1) |
| NFPA | 20-2016 | Standard for the Installation of Stationary Pumps for Fire Protection | 3.2.4.9.(4) 3.2.5.18 .(1) |
| NFPA | 24-2013 | Standard for the Instal lation of Private Fire Service Mains and Their Appurtenances | 7.2.11.1 .(1) |
| NFPA | 68-2013 | Standard on Explosion Protection by Deflagration Venting | 3.3.6.3.(1) 3.3.6.4.(2) 3.3.6.4.(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| NFPA | 72-2019 | National Fire Alarm and Signaling Code | 3.2.4.20 .(17) 6.9.4.4.(3) 9.10.19.1 .(2) 9.10.19.3 .(4) |
| NFPA | 80-2013 | Standard for Fire Doors and Other Opening Protectives | 3.1.8.5.(2) 3.1.8.12 .(2) 3.1.8.16 .(1) 3.1.9.1.(5) 3.13.3.1 .(2) 9.10.9.9 .(5) 9.10.13.1 .(1) |
| NFPA | 82-2014 | Standard on Incinerators and Waste and Linen Handling Systems and Equipment | 6.2.2.1.(1) 9.10.10.5 .(2) |
| NFPA | 91-2015 | Standard for Exhaust Systems for Air Convey ing of Vapors, Gases, Mists and Noncombustible Particulate Solids | 6.3.4.3.(1) |
| NFPA | 96-2014 | Standard for Ventilation Contr ol and Fire Protection of Commercial Cooking Operations | 3.2.4.8.(2) 3.6.3.5.(1) 6.3.1.6.(1) |
| NFPA | 105-2013 | Standard for Smoke Door Ass emblies and other Opening Protectives | 3.1.8.5.(3) 3.1.8.5.(7) |
| NFPA | 130-2023 | Standard for Fixed Guideway Transit and Passenger Rail Systems | 3.13.7.1 .(1) |
| NFPA | 211-2019 | Standard for Chimneys, Firepla ces, Vents and Solid Fuel-Burning Appliances | 6.3.3.2.(2) 6.3.3.3.(1) |
| NFPA | 701-2023 | Standard Methods of Fire T ests for Flame Propagation of Textiles and Films | 3.14.1.6 .(1) 3.14.2.5 .(1) 3.17.2.5 .(1) |
| NFRC | 100-2014 | Procedure for Determining Fenestration Product U-Fact ors | 12.3.1.2 .(1) |
| NFRC | 200-2014 | Procedure for Determining Fenestration Product Solar Heat Gain Coefficient and Visible Transmittance at Normal Incidence | 12.3.1.2 .(1) |
| NLGA | 2017 | Standard Grading Rules for Canadian Lumber | 1.4.1.2.(1) of Division A 9.3.2.1.(1) Table 9.3.2.1 . Tables 9.23.4.2 .-A to 9.23.4.3 .-J |
| NSF | NSF/ANSI 46-2010 | Evaluation of Components and Devices Used in Wastewater Treatment Systems | 8.6.2.1.(2) |
| NSF | NSF/ANSI 61-2013 | Drinking Water System Components - Health Effects | 7.2.10.7 C.(1) |
| SMACNA | ANSI/SMACNA 006- 2006 | HVAC Duct Construction Standards - Metal and Flexible | 9.33.6.5 .(2) 9.33.6.7 .(9) 9.33.6.7 .(10) |
| SPRI | ANSI/GRHC/SPRI VR-1- 2018 | Procedure for Investigating Resistance to Root or Rhizome Pen etration on Vegetative Roofs | 5.6.1.2.(2) |
| TPIC | 2019 | Truss Design Procedures and Specifications for Light Meta l Plate Connected Wood Trusses | 9.23.14.11 .(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| UL | ANSI/CAN/UL/ULC 300- 2019 | Standard for Fire Testing of Fi re Extinguishing Systems for Protection of Commercial Cooking Equipment | 6.9.1.3.(1) |
| UL | ANSI/UL-1784-2015 | Standard for Air Leakage Tests of Door Assemblies and Other Opening Protectives | 3.1.8.4.(4) |
| UL | UL 2034-2008 | Single and Multiple Station Carbon Monoxide Alarms | 9.33.3.9C.(1) |
| ULC | CAN/ULC-S101-14 | Standard Method of Fire Enduran ce Tests of Building Construction and Materials | 2.2.1.8.(4) 2.2.1.10 .(1) 3.1.5.7.(2) 3.1.5.14 .(5) 3.1.5.14 .(6) 3.1.5.15 .(3) 3.1.5.15 .(4) 3.1.7.1.(1) 3.1.11.7 .(1) 3.2.3.8.(1) 9.10.16.3 .(1) |
| ULC | CAN/ULC-S102-10 | Standard Method of Test for Surface Burn ing Characteristics of Building Materials and Assemblies | 3.1.5.24 .(1) 3.1.12.1 .(1) Table 5.9.1.1 . Table 9.23.17.2 .-A 9.29.5.2 .(1) |
| ULC | CAN/ULC-S102.2-18 | Standard Method of Test for Surface Burning Characteristics of Flooring, Floor Coverings, and Miscellaneous Materials and Assemblies | 3.1.12.1 .(2) 3.1.13.4 .(1) 9.27.12.1 .(4) 9.27.13.1 .(2) |
| ULC | CAN/ULC-S102.3-2018 | Standard Method of Fire Test of Light Diffusers and Lenses | 3.1.13.4 .(1) |
| ULC | CAN/ULC-S102.4-17 | Standard Method of Test for Fire and Smoke Characteristics of Electrical Wiring, Cables and Non-Metallic Raceways | 3.1.4.3.(2) 3.1.5.21 .(2) 3.1.5.23 .(2) |
| ULC | CAN/ULC-S104-15 | Standard Method for Fire Tests of Door Assemblies | 3.1.8.4.(1) 3.2.6.5.(3) |
| ULC | CAN/ULC-S105-16 | Standard Specification for Fire Door Frames Meeting the Perfo rmance Required by CAN/ULC-S104 | 9.10.13.6 .(1) |
| ULC | CAN/ULC-S106-15 | Standard Methods for Fire Tests of Window and Glass Block Assemblies | 3.1.8.4.(1) |
| ULC | CAN/ULC-S107-19 | Standard Methods for Fire Tests of Roof Coverings | 3.1.15.1 .(1) |
| ULC | CAN/ULC-S109-14 | Standard Method for Flame Tests of Flame-Resistant Fabrics and Films | 2.2.1.14 .(1) 3.1.16.1 .(1) 3.6.5.2.(2) 3.6.5.3.(1) 3.14.1.6 .(1) 3.14.2.5 .(1) 3.17.2.5 .(1) 9.33.6.3 .(1) |
| ULC | CAN/ULC-S110-13 | Standard Methods of Test for Air Ducts | 3.6.5.1.(2) 3.6.5.1.(5) 9.33.6.2 .(2) 9.33.6.2 .(4) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| ULC | CAN/ULC-S111-13 | Standard Method of Fi re Tests for Air Filter Units | 6.2.3.13 .(1) 9.33.6.14 .(1) |
| ULC | CAN/ULC-S112-10 | Standard Method of Fire Test of Fir e-Damper Assemblies | 3.1.8.4.(1) |
| ULC | CAN/ULC-S112.1-10 | Standard for Leakage Rated Dampers for Use in Smoke Control Systems | 3.1.8.4.(3) 6.3.2.7.(3) |
| ULC | CAN/ULC-S112.2-07 | Standard Method of Fir e Test of Ceiling Firestop Flap Assemblies | 3.1.9.4.(2) 3.6.4.3.(2) 9.10.13.14 .(1) |
| ULC | CAN/ULC-S113:2016 | Standard Specification for Wood Core Doors Meeting the Performance Required by CAN/ULC-S104 for Twenty Minute Fire Rated Closure Assemblies | 9.10.13.2 .(1) |
| ULC | CAN/ULC-S114:2018 | Standard Method of Test for Determination of Non- Combustibility in Building Materials | 1.4.1.2.(1) of Division A |
| ULC | CAN/ULC-S115-11 | Standard Method of Fi re Tests of Firestop Systems | 3.1.5.19 .(3) 3.1.8.3.(3) 3.1.9.1.(1) 3.1.9.1.(2) 3.1.9.1.(3) 3.1.9.1.(6) 3.1.9.1.(7) 3.1.9.3.(1) 3.1.9.3.(2) 3.1.9.3.(4) 3.1.9.4.(4) 3.1.9.4.(7) 9.10.9.2 .(3) 9.10.9.6 .(1) 9.10.9.6 .(2) 9.10.9.8 .(1) 9.10.9.8 .(6) |
| ULC | CAN/ULC-S124-06 | Standard Method of Test for the Evalua tion of Protective Coverings for Foamed Plastic | 3.1.5.15 .(2) |
| ULC | CAN/ULC-S126-14 | Standard Method of Test for Fire Spread Under Roof-Deck Assemblies | 3.1.14.1 .(1) 3.1.14.2 .(1) |
| ULC | CAN/ULC-S134-13 | Standard Method of Fire Test of Exterior Wall Assemblies | 3.1.5.5.(1) 9.10.15.5 .(2) |
| ULC | ULC-S135-04 | Standard Test Method for t he Determination of Combustibility Parameters of Buildi ng Materials Using an Oxygen Consumption Calorimeter (Cone Cal orimeter) | 3.1.5.1.(2) |
| ULC | CAN/ULC-S136:2021 | Standard Method for Fi re Test of Sprinkler Protected Window Systems | 3.1.8.20 .(1) |
| ULC | CAN/ULC-S138-06 | Standard Method of Test for Fire Growth of Insulated Building Panels in a Full-Scale Room Configurati on | 3.1.5.7.(1) 3.1.5.7.(3) |
| ULC | CAN/ULC-S139:17 | Standard for Fire Test for E valuation of Integrity of Electrical Power, Data and Optical Fibre C ables | 3.2.6.5.(6) 3.2.7.10 .(2) 3.2.7.10 .(3) |
| ULC | CAN/ULC-S143-14 | Standard Method of Fire Tests for Non-Metallic Electrical and Optical Fibre Cable Raceway Systems | 3.1.5.23 .(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| ULC | CAN/ULC-S144-12 | Standard Method of Fire Re sistance Test - Grease Duct Assemblies | 3.6.3.5.(2) |
| ULC | CAN/ULC-S146-19 | Standard Method of Test f or the Evaluation of Encapsulation Materials and Assemblies of Materials for the Protection of S tructural Timber Elements | 3.1.6.5.(1) |
| ULC | S505-1974 | Standard for Fusible Links for Fire Protection Ser vice | 3.1.8.10 .(2) |
| ULC | CAN/ULC-S524:2019 | Standard for Installation of Fire Alarm Systems | 3.1.8.11 .(3) 3.1.8.14 .(3) 3.2.4.5.(1) 3.2.4.20 .(10) 3.2.4.20 .(15) 9.10.19.4 .(3) 9.10.19.6 .(2) |
| ULC | CAN/ULC-S531:2019 | Standard for Smoke Alarms | 3.2.4.20 .(2) 9.10.19.1 .(1) |
| ULC | CAN/ULC-S537:2019 | Standard for Verification of Fire Alar m Systems | 3.2.4.5.(2) 3.2.4.20 .(10) |
| ULC | CAN/ULC-S540-13 | Standard for Residential Fire and Life Safety Warning Systems: Installation, Inspection, Testing and Maintenance | 3.2.4.21 .(1) 9.10.19.8 .(1) |
| ULC | CAN/ULC-S553-14 | Standard for the Instal lation of Smoke Alarms | 3.2.4.20 .(13) 9.10.19.3 .(2) |
| ULC | CAN/ULC-S561-13 | Standard for Installati on and Services for Fire Signal Receiving Centres and Systems | 3.2.4.7.(4) 3.13.5.4 .(1) |
| ULC | CAN/ULC-S572:2017 | Standard for Photolumi nescent and Self-Luminous Exit Signs and Path Marking Systems | 3.4.5.1.(4.1) 9.9.11.3 .(3) |
| ULC | CAN/ULC-S610:2018 | Standard for Factory-Built Fireplace Systems | 9.22.8.1 .(1) |
| ULC | ULC-S628-93 | Standard for Fireplace Ins erts | 9.22.10.1 .(1) |
| ULC | CAN/ULC-S629:2016 | Standard for 650ºC Fa ctory-Built Chimneys | 9.21.1.3 .(1) |
| ULC | CAN/ULC-S639-M87 | Standard for Steel Lin er Assemblies for Solid Fuel-Burning Masonry Fireplaces | 9.22.2.3 .(1) |
| ULC | CAN/ULC-S701.1:2017 | Standard for Thermal Insulation, Polystyrene Boards | Table 5.9.1.1 . Table 9.23.17.1 .-A 9.25.2.2 .(1) 9.25.2.2 .(4) |
| ULC | CAN/ULC-S702.1-14 | Standard for Mineral Fibre Thermal Insulat ion for Buildings, Part 1: Material Specification | 3.1.6.3.(4) Table 5.9.1.1 . 9.10.9.8 .(3) Table 9.23.17.2 .-A 9.25.2.2 .(1) |
| ULC | CAN/ULC-S703-09 | Standard for Cellulose Fibre Insulation (CFI) for Buildings | Table 5.9.1.1 . 9.25.2.2 .(1) |
| ULC | CAN/ULC-S704.1:2017 | Standard for Thermal Insulation, Polyurethane and Polyisocyanurate Boards, Faced | Table 5.9.1.1 . Table 9.23.17.2 .A 9.25.2.2 .(1) |
| ULC | CAN/ULC-S705.1:2018 | Standard for Thermal Insulation – Spray Applied Rigid Polyurethane Foam, Medium Density - Material – Specific ation | Table 5.9.1.1 . 9.25.2.2 .(1) |
Table . (Cont’d) Documents Referenced in the Building Code Forming Part of Sentence .(1)
| Issuing Agency | Document Number | Title of Document | Code Reference |
|---|---|---|---|
| ULC | CAN/ULC-S705.2-05 | Standard for Thermal Insulation – Spray Applied Rigid Polyurethane Foam, Medium Density – Appli cation | Table 5.9.1.1 . 9.25.2.5 .(1) |
| ULC | CAN/ULC-S706.1:2016 | Standard for Wood Fibre Insulating Boards for Buildi ngs | Table 5.9.1.1 . 9.23.16.7 .(3) Table 9.23.17.2 .-A 9.25.2.2 .(1) 9.29.8.1 .(1) |
| ULC | CAN/ULC-S710.1:2019 | Standard for Bead-Applied One Component Po lyurethane Air Sealant Foam, Part 1: Material Specification | Table 5.9.1.1 . |
| ULC | CAN/ULC-S711.1:2019 | Standard for Bead-Applied Two Co mponent Polyurethane Air Sealant Foam, Part 1: Material Specification | Table 5.9.1.1 . |
| ULC | CAN/ULC-S716.1-12 | Standard for Exterior Insulation and Finish Systems (EIFS) – Materials and Systems | 5.9.4.1.(1) 9.27.14.1 .(1) 9.27.14.2 .(1) |
| ULC | CAN/ULC-S716.2-12 | Standard for Exterior Insulation and Finish Systems (EIFS) – Installation of EIFS Components and Water Resistive Barrier | 9.27.14.3 .(2) |
| ULC | CAN/ULC-S716.3-12 | Standard for Exterior Insulation and Finish Systems (EIFS) – Design Application | 9.27.14.3 .(1) |
| ULC | CAN/ULC-S717.1:2017 | Standard for Flat Wall Insulating Concrete Form (ICF) Units – Mate rial Properties | Table 5.9.1.1 . 9.15.4.1 .(1) |
| ULC | CAN/ULC-S741-08 | Standard for Air Barr ier Materials – Specification | 5.4.1.2.(2) |
| ULC | CAN/ULC-S742-11 | Standard for Air Barrier Assemblies – Speci fication | 5.4.1.2.(1) 5.4.1.2.(2) |
| ULC | CAN/ULC-S1001-11 | Standard for Integra ted Systems Testing of Fire Protection and Life Safety Systems | 3.2.9.1.(1) 9.10.1.2 .(1) |
| ULC | ULC/ORD-C199P-02 | Combustible Piping for Sprinkler Systems | 3.2.5.13 .(2) 3.2.5.13 .(5) |
| ULC | ULC/ORD-C1254.6-95 | Fire Testing of Restauran t Cooking Area Fire Extinguishing System Units | 6.9.1.3.(1) |
| USDA | October 1993 | Soil Survey Manual | 8.2.1.2.(2) |
| WT | October 20, 2016 | Port Lands Flood Protection and Enab ling Infrastructure Due Diligence Report | 1.3.3.6.(4) of Division C |
1.3.2.Abbreviations
1.3.2.1.Abbreviations of Proper Names (See Note A-1.3.2.1.(1))
(1) The abbreviations of proper names in this Code shall have the meanings assigned to them in Table .
Table 1.3.2.1. Abbreviations of Proper Names Forming Part of Sentence 1.3.2.1.(1)
| Abbreviation | Meaning |
|---|---|
| ACGIH | American Conference of Gover nmental Industrial Hygienists |
| ACI | American Concrete Institute |
| AHRI | Air-Conditioning, Heating and Refrigeration Institute |
| AISI | American Iron and Steel Institu te |
| ANSI | American National Standards Institute |
| APA | The Engineered Wood Association |
| APHA | American Public Health Association |
| ASCE | American Society of C ivil Engineers |
| ASHRAE | American Society of Heating, Refrigerating and Ai r-Conditioning Engineers |
| ASME | The American Society of Me chanical Engineers |
| ASPE | American Society of Plumb ing Engineers |
| ASSE | American Society of Sanit ary Engineering |
| ASTM | American Society for Testing a nd Materials |
| AWS | American Welding Socie ty |
| AWWA | American Water Works Association |
| BCMOH | British Columbia Ministry of Health |
| BNQ | Bureau de Normalisation du Québec |
| CAN | National Standard of Canad a designation The number or name following the CAN designation represents the agency under whose auspices the standard is issued. CAN1 designates CGA, CAN2 designates CGSB, CAN3 designates CSA, and CAN4 designates ULC. |
| CCBFC | Canadian Commission on Building and Fire Codes |
| CGSB | Canadian General Standards Board |
| CHC | Canadian Hydronics Council |
| CSA | CSA Group, formerly called Canadian Standards As sociation |
| CWC | Canadian Wood Council |
| DBR | Division of Building Research, known as the Institute for Research in Construction since 1985 |
| DOE | U.S. Department of Energy |
| EPA | Environmental Protection Agency |
| FINA | Fédération Internationale de Na tation |
| GRHC | Green Roofs for Healthy Ci ties |
| HC | Health Canada |
| HI | Hydronics Institute |
| HPVA | Hardwood Plywood & Veneer Association |
Table . (Cont’d) Abbreviations of Proper Names Forming Part of Sentence .(1)
[TABLE:1] Farm Buildings